縫前設備 縫制設備 縫制配件 整理設備 繡花機 內衣機械 服裝輔助設備 洗滌機械 二手服裝機械 其它服裝機械
上海榮計達儀器科技有限公司
會員1.png)
上海榮計達儀器科技有限公司
| 參 考 價 | 面議 |
產品型號
品 牌
廠商性質其他
所 在 地上海市
紡織服裝機械網采購部電話：0571-88918531
QQ:2568841715
聯系方式：查看聯系方式
更新時間：2024-02-10 18:22:42瀏覽次數：156次
聯系我時，請告知來自 紡織服裝機械網乳化瀝青粘結力測定儀,瀝青實驗儀器
乳化瀝青粘結力測定儀是專業瀝青檢測儀器，用于測定乳化瀝青稀漿封層混合料達到固化所需的時間，用以確定乳化瀝青稀漿封層混合料施工后早期開放交通的時間使用前務必仔細閱讀說明書。
Emulsified asphalt adhesion tester is a professional asphalt testing instrument used to determine the time required for the emulsified asphalt slurry seal mixture to fully cure, to determine the time of early open traffic after the construction of the emulsified asphalt slurry seal mixture. Be sure to read the instructions carefully before use.
乳化瀝青粘結力測定儀主要特點：
★符合‘JYJ052-2000’標準中‘TO754-2000’的試驗規范。
★既可以做室內試驗，也可以在施工現場使用；
★制作精良，使用方便，測試結果準確可靠。
Main features of emulsified asphalt bond tester:
★ Meet the test specifications of ‘TO754-2000’ in the ‘JYJ052-2000’ standard.
★ It can be used for indoor test or at the construction site;
★Excellent production, easy to use, accurate and reliable test results.
乳化瀝青粘結力測定儀主要技術參數:
★壓頭：橡膠墊直徑28.6mm，厚6.4mm
★測力板手：扭矩表A大扭矩不小于350N.cm，傳力桿直徑8cm
★圓型試模：①Φ60mm（內徑）×6mm（高）②Φ60mm（內徑）×10mm（高）
★重量：20KG
★外形尺寸：400x300x600mm
★環境溫度：≤35℃
★相對濕度：≤85%
Main technical parameters of emulsified asphalt bond tester:
★Indenter: rubber pad diameter 28.6mm, thickness 6.4mm
★ Force wrench: Torque meter A high torque is not less than 350N.cm, force rod diameter 8cm
★ Round test mode: 1Φ60mm (inside diameter) × 6mm (high) 2Φ60mm (inside diameter) × 10mm (high)
★ Weight: 20KG
★Dimensions: 400x300x600mm
★ Ambient temperature: ≤35°C
★ Relative humidity: ≤85%
乳化瀝青粘結力測定儀試驗步驟：
★將初凝后的試件置于粘結力試驗儀的氣動橡膠墊下面，放置15分鐘。
★將氣動橡膠墊底座壓在試件上面，用自行車氣筒或空氣壓縮機向儀器加壓。
★當儀器壓力表達到0.72Mpa時，保持此壓力，此時橡膠底座對試件的壓力為193Kpa。
★達到壓力并保持不變后，將測扭矩扳手測力表歸零并套住氣缸上端，在0.7-1秒內平穩、水平地扭轉90-120度，并讀取扭矩儀讀數。
★升起橡膠底座，并擦干凈底部待下次測試。
★此后每隔15分鐘重復上述步驟。
★當固化時間較長時，間隔時間可延長到30分鐘重復試驗一次。
★重復試驗直至達到A大扭矩，且此扭矩為定值時為止。
★記錄達到大扭矩時的時間即固化時間，固化時間加上初凝時間就是稀漿混合料的‘早期開放交通時間’
Emulsified asphalt adhesion tester test steps:
★ Place the test piece after initial setting under the pneumatic rubber pad of the adhesion tester and leave it for 15 minutes.
★ Press the base of the pneumatic rubber pad on the test piece and pressurize the instrument with a bicycle air pump or air compressor.
★ When the pressure of the instrument is expressed to 0.72Mpa, keep this pressure. At this time, the pressure of the rubber base on the test piece is 193Kpa.
★After reaching the pressure and keeping the same, return the torque wrench force gauge to zero and cover the upper end of the cylinder, and smoothly and horizontally twist 90-120 degrees in 0.7-1 seconds, and read the torque meter reading.
★ Raise the rubber base and wipe the bottom clean for the next test.
★ Repeat the above steps every 15 minutes thereafter.
★ When the curing time is long, the interval can be extended to 30 minutes to repeat the test.
★ Repeat the test until the A high torque is reached, and the torque is constant.
★ Record the time when the high torque is reached, that is, the curing time. The curing time plus the initial setting time is the 'early open traffic time' of the slurry mixture.
乳化瀝青粘結力測定儀試驗報告：
報告應記述下列事項：
配制乳化瀝青的乳化劑及瀝青的品種，乳化劑用量，瀝青含量。
礦料種類及級配。
乳化瀝青稀漿封層混合料的固化時間。
Emulsified asphalt adhesion tester test report:
The report should describe the following:
Emulsified asphalt emulsifier and asphalt varieties, emulsifier dosage, asphalt content.
Mineral material types and grading.
The curing time of the emulsified asphalt slurry seal mixture.
乳化瀝青粘結力測定儀注意事項：
儀器長期不使用，每半個月將活塞桿上下活動，如活塞過緊，需加潤滑機油。測扭矩版搜也需每月轉動幾次。
Precautions for emulsified asphalt adhesion tester:
The instrument will not be used for a long time, and the piston rod will move up and down every half month. If the piston is too tight, it needs to be lubricated with oil. The torque test version also needs to be rotated several times a month.
乳化瀝青粘結力測定儀裝箱單
序號
1 主機 1臺
2 試模 6個
3 扭矩扳手 1把
4 說明書 1份
5 合格證 1份
Emulsified asphalt adhesion tester packing list
Serial number
1 host 1
2 tryout 6
3 torque wrench 1
4 instructions 1 copy
5 certificate 1
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
紡織服裝機械網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
